Best Value Available! 2024 Realistic Verified Free D-PDC-DY-23 Exam Questions
Pass Your Exam Easily! D-PDC-DY-23 Real Question Answers Updated
NEW QUESTION # 95
ACLs have which two actions?
- A. Redistribute or forward.
- B. Modify or drop.
- C. Permit or deny.
- D. Forward or erase.
Answer: C
NEW QUESTION # 96
Which two options describe differences between Layer 2 and Layer 3 QoS? (Select 2)
- A. 802.1P trust-maps only function on untagged VLANs.
- B. DSCP uses the same Type of Service Field that IP Precedence uses.
- C. IP Precedence implements 64 unique traffic classes for packet queueing.
- D. Class of Service priorities are encoded in the 802.1Q header.
Answer: B,D
NEW QUESTION # 97
What is an advantage of UFD?
- A. Reduces connectivity loss.
- B. Prevents the loss of upstream connectivity.
- C. Detects the loss of downstream connectivity.
- D. Reduces network complexity.
Answer: D
NEW QUESTION # 98
What is a characteristic of a static LAG on a Dell Networking OS10 switch?
- A. Does not allow reconfiguration of the predefined ports
- B. Uses LACP for management only
- C. Does not use any protocol for configuration and management
- D. Uses LACP for configuration only
Answer: C
NEW QUESTION # 99
Match the OSPF router types.
There are more descriptions than router types.
Answer:
Explanation:
NEW QUESTION # 100
What are mandatory LLDPDU TLV's?
- A. 0
- B. 0456
- C. 0124
- D. 0123
Answer: D
NEW QUESTION # 101
When installing OS10 on a switch from a USB drive, what format is used for the file system?
- A. HFS+
- B. NTFS
- C. FAT32
- D. HFS
Answer: C
NEW QUESTION # 102
Refer to the exhibit.
Which three commands are used when deploying an automated Leaf and Spine topology using SFS?
(Select 3)
- A. Spine1(conf)# smartfabric l3fabric enable role SPINE
- B. Spine1(conf)# smartfabric l3fabric enable role SPINE downstream ethernet 1/1/1-1/1/2
- C. Spine1(conf)# smartfabric l3fabric enable role SPINE prefer
- D. Leaf2(conf)# smartfabric l3fabric enable role LEAF vlti ethernet 1/1/10
- E. Leaf1(conf)# smartfabric l3fabric enable role LEAF vlti ethernet 1/1/10
Answer: C,D,E
NEW QUESTION # 103
A network administrator is implementing VRRP on a switch and has configured VLAN 10 to use a matching VRRP group ID 10.
Which two commands indicate default VRRP settings? (Select 2)
- A. OS10(conf-vlan10-vrid-10)# advertise-interval secs 10
- B. OS10(conf-vlan10-vrid-10)# preempt
- C. OS10(config)# vrrp version 2
- D. OS10(conf-vlan10-vrid-10)# priority 10
Answer: B,C
NEW QUESTION # 104
What two types of networking information are synchronized between VLT peer nodes? (Select 2)
- A. IPv6 routes
- B. MAC address tables
- C. ARP entries
- D. VRF instances
- E. IPv4 routes
Answer: B,C
NEW QUESTION # 105
Which value is used to determine the primary node role in a default VLT primary election?
- A. Highest system MAC address
- B. Lowest system MAC address
- C. Lowest management IP address
- D. Highest management IP address
Answer: A
NEW QUESTION # 106
In a PIM Sparse Mode based multicast topology, what role does the Rendezvous Point provide?
- A. The node is used to provide (*,G) on a Layer 2 shared segment.
- B. The first-hop router is used to provide routing between the source and receiver.
- C. The location PIM sends traffic before invoking SPT.
- D. The node is used to provide (S,G) across a Layer 3 boundary.
Answer: C
NEW QUESTION # 107
What is the default lease time in hours for an address lease in DHCP?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 108
Refer to the exhibit.
A network administrator is attempting to configure a static route on OS10-A to reach the loopback0 address on OS10-B.
Why is the ping failing?
- A. The route is pointing to the wrong next-hop on OS10-A
- B. OS10-B must share a common VRF
- C. Interface Eth1/1/2 is a member of the wrong VRF on OS10-A
- D. The route has been added to the incorrect VRF on OS10-A
Answer: D
NEW QUESTION # 109
Which interface b/pes can be used with Uplink Failure Detection?
- A. Logical port or port channel
- B. Physical port or port channel
- C. VLAN or physical port
- D. Physical port or logical port
Answer: B
NEW QUESTION # 110
What does the "%" character do within the banner login % command?
- A. It is a special character that forms a border around the warning banner text.
- B. This character indicates the start and end of text entry mode for Ihe banner command.
- C. When entering the text for a warning banner, it causes the banner to print in bold text.
- D. It is a wild-card character for the required login password when the banner appears.
Answer: B
NEW QUESTION # 111
From which range can a network administrator choose when setting the RSTP priority value?
- A. 1-64
- B. 0-61440
- C. 0-614400
- D. 1-6400
Answer: B
NEW QUESTION # 112
What should be disabled on an interface before disabling LLDP transmit capability?
- A. VLAN 1
- B. LLDP-MED
- C. STP
- D. Loop Guard
Answer: B
NEW QUESTION # 113
A customer has disabled LLDP on the management interface of the switch.
What is the proper command to re- enable it?
- A. OS10(config)# interface mgmt 1/1/1
OS10(conf-if-ma-1/1/1)#lldp tly-select
OS10(conf-if-ma-1/1/1)#lldp dot1tlv - B. OS10(config)# interface mgmt 1/1/1
OS10(conf-if-ma-1/1/1)#lldp transmit
OS10(conf-if-ma-1/1/1)#lldp receive - C. OS10(config)# lldp enable OS10(config)#lldp transmit OS10(config)#lldp receive
- D. OS10(config)# interface mgmt 1/1/1
OS10(conf-if-ma-1/1/1)#lldp med enable
OS10(conf-if-ma-1/1/1)#lldp timer 10
Answer: B
NEW QUESTION # 114
What is the maximum number of LLDP neighbors supported per system with OS10?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 115
......
Actual Questions Answers Pass With Real D-PDC-DY-23 Exam Dumps: https://www.prepawaytest.com/EMC/D-PDC-DY-23-practice-exam-dumps.html
D-PDC-DY-23 Dumps Prepare Your Exam With 205 Questions: https://drive.google.com/open?id=1p4nFnfwlLANKRh0pltQS-eviv-5rcI7R